8 × 10/100 Mbps PoE ports,2 × Gigabit RJ45 port

Total PoE Power Budget 60 W

Support 802.1Q VLAN

Support PoE watchdog to detect and restart the cameras that do not respond

Support STP/RSTP Loop prevention

Support cable detection to locate failure

Up to 300 m Long Range PoE Transmission

6 kV Surge Protection

General

ShellMetal material

Net Weight0.54 kg (1.19 lb)

Gross Weight1.08 kg (2.38 lb)

Dimensions (W × H × D)217.6 mm × 27.6 mm × 108.5 mm (8.57'' × 1.09'' × 4.27'')

Operating Temperature0 °C to 40 °C (32 °F to 104 °F)

Storage Temperature-40 °C to 85 °C (-40 °F to 185 °F)

Operating Humidity5% to 95% (no condensation)

Relative Humidity5% to 95% (no condensation)

Power SupplyDC54 V,1.2 A

Installation ModeDesk-Mounted,Wall-Mounted

Max. Power Consumption65 W

Power Consumption in Idle5 W

Surge Protection6 kV

Network Parameters

Ports8 × 10/100 Mbps PoE port,2 × Gigabit RJ45 port

MAC Address Table4 K

Switching Capacity

Whole-Device Performance: 9.6 Gbps

Port Performance: 5.6 Gbps

Packet Forwarding Rate

Whole-Device Performance: 7.14 Mpps

Port Performance: 4.17 Mpps

Internal Cache2 Mbits

PoE Power Supply

PoE StandardIEEE 802.3af,IEEE 802.3at

PoE Power PinEnd-span: 1/2(-), 3/6(+)

PoE PortPoE: Ports 1 to 8

Max. Port Power30 W

PoE Power Budget60 W

Software Function

Long Range

Ports 1 to 8: up to 300 m.

Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 8: port isolation mode to improve network security

Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE WatchdogPorts 1 to 8: auto detect and restart the cameras that do not respond.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default.

Support 802.1D STP.

Suppport 802.1w RSTP.

VLAN

VLAN is used for network scale planning and network health improvement.

Support 802.1Q.

Configurable VLAN ID from 1-4094.

Support Trunk, Access port mode.

Support Max. 4094 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported:

1. Display the port rate.

2. Display the port bandwidth utilization rate.

3. Display the PoE power usage.

4. Display topology information.

5. Display the alarm status.

6. Restart ports and devices.

7. Enable port long-rage mode.

8. Remotely upgrade the device.

System Maintenance

Support device management via web.

Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses.

Support Super IP, which is a fixed IP address (10.180.190.200) for direct access.

Support management via Hik-Central Pro.

Support remote management via Hik-Partner Pro.

Support cable detection.

Supports 802.1ab LLDP for peer device discovery.

Support port mirroring for fault locating.

Approval

EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)

SafetyCB (IEC 62368-1)

ChemistryCE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC) No.1907/2006)